This manual contains maintenance procedures for service personnel. It is divided .. Cn. Lexmark. Cdn. Lexmark. Cn. Lexmark. Cdn. Lexmark. Lexmark C C C C Service Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Lexmark C C Service Manual. xx, 4xx. Go Back. Previous. Next. Assembly 1: Covers . 4. 3. 1. 6. 5. 8. 7. 2. 9 www MK-Electronic de.

Author: Netilar Mikam
Country: Eritrea
Language: English (Spanish)
Genre: Sex
Published (Last): 9 January 2016
Pages: 32
PDF File Size: 15.46 Mb
ePub File Size: 11.89 Mb
ISBN: 302-6-25902-855-1
Downloads: 25340
Price: Free* [*Free Regsitration Required]
Uploader: Vikinos

Clear Log xx, 4xx The printed event log can be faxed to your next level of support for verification or diagnosis. If you receive a new low-voltage power supply with a voltage selector switch Cbe sure to set the switch to the correct setting for your voltage requirements before installing the low-voltage power supply. Page xx, 4xx Remove the exit deflector and the manula full sensor flag D.

Printhead Service Check xx, 4xx Printhead service check This service check includes the following errors: Preface xx, 4xx Preface This manual contains maintenance procedures for service personnel.

Swing the rear of the lower frame away from the printer to access the tray present sensor latches. First Transfer xx, 4xx Step 4a: Be sure to note the maanual for re-installation.

Pull corner of cable cover B away from the right side to access the sensor posts C. The wrong code, or wrong level of code could lead to a malfunction or render the device inoperable.

The laser notice label may be affixed to this printer. The following illustration and table list the paper jams that can occur and the location of each jam.

If the bushing is damaged, remove it by pressing the tabs on each side. The following illustration and table list the paper jams that can occur and the location of each jam. Page xx, 4xx Remove the two screws B from the inside left side. Page msnual, 4xx Remove the four screws B securing the cable cover, and remove the cable cover.


Menu Map xx, 4xx Menu map This menu map identifies menus available to customers. Notices And Safety Information xx, 4xx Notices lexmarj safety information The laser notice label may be affixed to this printer. Slide the antenna cable and cable through the hole in the bracket. Close the front cover, and slightly lift the front of the printer to get better access.

Make Your Selection

Second Transfer xx, 4xx Step 4b: The cable may have come loose from the HVPS. Replace the For example, the distance between these two Replace the Open the toner supply door. The third drawer is compatible only with the Lexmark Cdtn model. The Back, Menu, and Stop buttons are located to the left of the display and the navigation buttons are located below the display.

The settings affected include paper size, envelope size, PCL symbol set, code pages, and units of measure. Page xx, 4xx On the right side, loosen the screw F with a screwdriver, and hold the ACM in place as you use your fingers to remove the screw.

Page xx, 4xx Disconnect the left fuser spring H from the fuser. Remove the two screws G on the right of the main drive gear assembly Lift the main drive gear assembly, and remove.

X540n removal requires a servicd, long-shank Phillips screwdriver at least 8 in. Because of the charge difference between the toner on the developer roll and the electrostatic image created by the laser, the toner will cling to the PC. Toner Cartridge Contacts xx, 4xx Remove the three screws B.

Page 11 xx, 4xx X540n I-laserprodukter betragtes ikke som farlige. Is the tray damaged? For each color, the toner cartridge engages the photoconductor so it applies serrvice to the surface. Page xx, 4xx Rotate the release lever C in a counterclockwise direction with a springhook or needlenose pliers to decouple the ITU while pulling the ITU toward the front. Waste toner bottle removal The waste toner bottle is not a FRU.

  BGI 5006 PDF

To remove the cable, be sure to unwrap the toroid. Fuse Page – Step 6: It is divided into the following chapters: Diagnostic information Start CAUTION Unplug power cord from the electrical outlet before you connect or disconnect any cable or electronic board or assembly for personal safety and to prevent damage to the printer.


Page xx, 4xx Reinstall the rear shield to protect the controller board, and turn the printer so the rear shield rests on the table and the bottom is facing you.

Insert the bottom edge inside the frame, and then push down on the top edge to clear the top cover. Once the printer has been restored to its default levels, do the following: Remove the screw A securing the fuser exit sensor.

Page xx, 4xx serial number toner cartridge contacts viewing parts catalog service checks removals 90x. Selecting Paper US fed as well as non-recycled paper. With one hand, gently pull the exit deflector towards the rear, and with the other hand, press to unsnap the tabs C.

Imaging Kit The following actions can be taken: Reinstall the three screws holding the ACM to the printer. The following actions can be taken: Remove the media tray.

Author: admin